Touch Instrument Tools


Professional Digital Alcohol Tester Breathalyzer TQ00141

$92.00

1. Instructions

a) Press and hold the Power switch to turn the unite on. The cumulative test count will be displayed as you hold the Power switch down.

b) Release the Power switch. There will be a countdown from 234 to 0 as the unit warms up.

c) Secure your lips around the mouthpiece and blow sharply and steadily into the unit for about 4 seconds. You will hear two beeps when the device is done taking the breath sample. You will se the digit0moving left to right in the display as the device analyzes the sample.

d) When analysis is complete,you will see the blood alcohol concentration (BAC) results displayed.

e) The results will be shown for about 15 seconds. The unit will then shut itself off.

f) If the device cannot take a successful sample, you will see in the display and the unit will shout itself off.

 

2. Understanding your Results(BAC reading)

Your Reading

Your Range

Description

Device Behavior

0.00% to 0.01% or 0.00 ‰ to 0.10‰ or 0.00mg/l to 0.05mg/l

Safe range

Little/no alcohol intake

(No special warnings.)

0.02% to 0.04% or 0.20‰ to 0.40‰ or 0.10mg/l to 0.20mg/l

Moderate* range.

Increased alcohol intake

(No special warnings.)

0.05% and over or 0.50‰ and over or 0.25mg/l and over.

Warning * range.

Ability to drive may be impaired.

Flashing WARN indicator and repeating beep

* Drinking alcohol in ANY amount may impair the ability to drive. There is no safelevel of alcohol intake before driving. Dont drink and drive.

 

1. Indication of B.A.C. 0.0 to 4.00 ‰ or 0.0 to 0.400%BAC or 0.0 to 2.00 mg/l BrAC by LED display
2. Sensor: Semiconductor type alcohol sensor
3. Accuracy: ±0.01%BAC at 0.05%BAC
4. Mouthpiece: use
5. Power: Two 1.5V "AA" size alkaline batteries / Auto Power off
6. Weights: 115g (Including Batteries)
7. Dimension(mm): 124 (height) X 56 (width) X 41 (thickness) MAX
8. Audible warnings: 3 steps beep warning of alcohol detection with LED display

 

Warnings

a) Wait at least 20 minutes after eating or drinking before testing. Alcohol remaining in mouth,or even excess saliva,may interfere with testing. This includes alcohol-based mouthwash or similar products.

b) Avoid testing in high wind or enclosed spaces. Poor ventilation may also lengthen the time required for warm up between tests.

c) Do not blow smoke, saliva or other contaminants into the mouthpiece, as the sensor may become damaged.

d) Do not use IT as tool to drink and drive.

e) Kepp out of extreme temperatures and out of the reach of children.

f) To maintain accuracy, we recommend replacing the alcohol sensor module inside approximately every 300 tests, or if damaged by improper testing or handing.

g) Warnning display Flo if you see FIO in the display, the creath sample was not strong enough for measurement. Please try again and make sure the breath is strong and steady during sampling.

h) Warnning Display bAt: if you see bAt in the display, the battery power is low please replace the batteries.

 

 

Remove the battery cover at the bottom of the unit and replace.the old batteries with two new 1.5V"AA" batteries. make sure to properly align the batteries by looking at the +/-marks.

Notice. Please don't use Managaese Battery. Use Alkaline Battery only.


Add to Cart:

  • Model: TQ00141
  • Shipping Weight: 0.8lbs




This product was added to our catalog on Monday 19 October, 2020.

Your IP Address is: 44.203.219.117
Copyright © 2024 Touch Instrument Online Shop. Powered by Zen Cart